定制弧形防撞墻模具 各種形狀防撞墻模具模板 樂豐模具 防撞墻模具屬于大型鋼制模具，特使應用于高速公路，鐵路，橋梁，等工程施工上的主要水泥防護墻的塑形鋼模具，采取鋼制模具預制水泥防撞墻的優勢所在其實就是為了降低預制過程中的繁瑣事項，同時還能夠增加每天的生產數量，省去人工的勞動力匱乏現象的發生，防撞墻鋼模具也叫做防撞護欄鋼模具，作用就是為了提升行車的安全性。

 

防撞墻模具當預埋件與護欄鋼筋出現沖突時，適當移動鋼筋位置，保證預埋件位置準確，清掃預制構件表面，并用水沖洗干凈，水泥防撞墻模具鑿毛上根據測量確定的防護欄邊線，采用人工對護欄邊線范圍內的箱梁表面進行鑿毛處理，鑿除混凝土表面的水泥砂漿和松弱層，并用水沖洗干凈，水泥防撞墻模具鋼筋的加工及安裝主線邊防撞護和匝道防撞護欄順橋向每2m設置一道假縫，嚴格按照設計圖紙對上述預埋件進行埋設，預埋件安裝要做到不遺漏，定位準確。設計伸縮縫處鋼筋要斷開，斷面要整齊。清掃預制構件表面，并用水沖洗干凈。模具生產過程中的細節會影響模具的使用和性能，對模具使用后保養方式要注重，保證模具的使用次數。

 When there is conflict between the embedded parts and the guardrail reinforcement in the anti-collision wall mould, the position of the reinforcement shall be moved appropriately to ensure the accuracy of the embedded parts position. The surface of the prefabricated components shall be cleaned and washed with water. On the chisel of the cement anti-collision wall mould, the edge line of the protective fence determined according to the measurement shall be chiseled. The surface of the box girder within the edge line of the protective fence shall be roughened manually to remove the cement mortar and the Loosen the weak layer and wash it with water. Process and install the mold reinforcement of cement anti-collision wall. Set a dummy joint every 2m along the bridge direction for the main line border protection and ramp anti-collision guardrail. Bury the above embedded parts in strict accordance with the design drawings. The installation of the embedded parts shall be complete without omission and accurate positioning. The reinforcement at the designed expansion joint shall be disconnected and the section shall be neat. Clean the surface of prefabricated components and wash them with water. The details in the mould production process will affect the use and performance of the mould. We should pay attention to the maintenance mode of the mould after use to ensure the use times of the mould.

防撞墻模具正好處于兩塊模板的接縫處，安裝模板時要在鋼筋上纏上海綿條防止漏漿；模具安裝好后，根據所需規格制造鋼筋籠；將攪拌均勻的混凝土從攪拌機卸出，傾倒置斗車上，經人工定量放料與鋼筋籠進模具，然后由輸送帶運至振臺平臺進行手動抹平，即可做成型，再放置平地進行自然保養，自然養護24小時候便可脫模。