進口氣瓶減壓閥（歐美品牌）德國洛克 

進口氣瓶減壓閥結構特點:

進口氣瓶減壓閥，單級式膜片減壓結構，不銹鋼膜片壓力傳輸，輸出壓力穩定，適用于純凈氣體、標準氣體、腐蝕性氣體等。用用于石油化工、化纖、照明電器、熱處理、冶金、玻璃、食品、醫藥、電子、國防航天、航空等主導領域。

進口氣瓶減壓閥規格參數：

部位名稱      材質

◆母體          316l，brass

◆上蓋          316l，brass

◆膜片          316l

◆過濾網        316l（10μm）

◆閥座          pctfe，ptfe，vespel

◆彈簧          316l

◆閥芯頂桿      316l

壓力特性參數：

◆輸入壓力：15mpa，20mpa，25mpa   6000psi,3000psi,500psi

◆輸出壓力：0-0.1mpa，0-1mpa，0-5mpa，0-10mpa，0-15mpa  0～25,0～100,0～300,0-3000psi

◆進口規格：g1/4,g1/2,g5/8,g1

◆出口規格：g1/4,g1/2,g5/8,g1，卡套

◆測試壓力：1.5倍的*輸入壓力

◆適用溫度：-40°f 至＋165°f（-40℃至＋74℃）

進口氣體氣瓶減壓閥安裝說明： 

1、用下扳將減壓器進出氣接頭螺紋與氣瓶閥螺紋或高低壓側管路可靠的連接，一防止氣體泄漏。請勿轉動減壓器本體，應夾持本體，轉動螺母擰緊。

2、在安裝過程中，應確保減壓器進、出氣接頭與減壓器連接處不會發生松動，否則將會導致氣體泄漏，造成安全重大隱患。

3、徹底清除氣瓶和管路系統與減壓器連接位置處的油污、水及灰塵，一旦雜質進入氣體減壓器內，將會導致污染氣體，阻塞氣體通道或產生其他麻煩。

4、如果管路上的螺紋變形，無法與氣體減壓器順利地裝上時，就不要強行連接，否則會導致管路系統及氣體減壓器上的螺紋損壞，從而引起嚴重事故。

Installation instructions for pressure reducing valve of imported gas cylinder:
1. Use the pull down to connect the inlet and outlet gas connection thread of the pressure reducer with the screw of cylinder valve or the pipeline at the high and low pressure side reliably, to prevent gas leakage. Do not turn the reducer body. Hold the body and tighten the nut.
2. During installation, it is necessary to ensure that the connection between the inlet and outlet joints of the pressure reducer will not be loose, otherwise, the gas leakage will be caused and the safety and major hidden danger will be caused.
3. Thoroughly remove oil, water and dust at the connection position between cylinder and pipeline system and pressure reducer. Once impurities enter the gas pressure reducer, it will cause pollution of gas, block gas channel or cause other troubles.
4. If the thread on the pipeline is deformed and cannot be installed smoothly with the gas pressure reducer, do not forcibly connect it, otherwise, it will cause the screw damage on the pipeline system and gas pressure reducer, which will cause serious accidents.
 

進口氣瓶減壓閥產品簡介：

在物理化學實驗中，經常要用到氧氣、氮?dú)?、氫氣、氬氣、二氧化碳等氣體。這些氣體都是貯存在專用的高壓氣體鋼瓶中，使用時通過氣瓶減壓閥使氣體壓力降至實驗所需范圍，再經過其它控制閥門細調，使氣體輸入使用系統。德國洛克《DE LOCKE》進口氣瓶減壓閥就是將氣瓶中的高壓氣體減為實驗及使用工況所需壓力的減壓裝置。

Introduction to the imported gas cylinder pressure reducing valve products:
In the physical and chemical experiments, oxygen, nitrogen, hydrogen, argon, carbon dioxide and other gases are often used. These gases are stored in special high pressure gas cylinders. When used, the gas pressure is reduced to the required range of the experiment through the pressure reducing valve of the cylinder. Then, the gas is input into the system through other control valves. The pressure reducing valve of imported cylinder of Locke, Germany is a pressure reducing device which reduces the high pressure gas in the cylinder to the pressure required for the test and operation conditions.