井口篦子模具

   鑄鐵井蓋在馬路上的應用是非常常見的，保證著我們的行駛安全，匯淀井蓋今天就來跟大家講講關于鑄鐵井蓋安裝的注意點。

1．選用鑄鐵井蓋的內徑（或內長X寬）一定要大于等于預留井口尺寸，否則將大大影響承載力；

2．在安裝時井座與混凝土地面結合面一定要貼實，不得有懸空的地方，否則在施工安裝中會被壓路機壓壞和影響使用壽命；

3．在瀝青路面上安裝鑄鐵井蓋時，一定要注意避免施工機械直接碾壓井座，在路面施工時，應在路面預留比井座略大的孔，在瀝青鋪完后安置。不知道大家有沒有注意過，近年來大街上丟井蓋的案件越來越少了。這固然要?dú)w功于社會治安的持續進步，但另一方面，“井蓋科技”的進步也不可小覷。

澆注位置的確定原則

a) 澆注時主要加工表面，主要工作面和受力面應盡量放在底部和側面，以防止產生砂眼，氣孔，夾渣等缺陷。
b) 對于凝固體收縮較大的鑄件合金，應滿足順序凝固的原則，鑄件厚實部分應盡可能置于上方，利于冒口補縮。Grate mould

The application of cast iron well cover on the road is very common, which ensures our driving safety. Huidian well cover will talk about the points for attention about the installation of cast iron well cover today.

1. The inner diameter (or inner length x width) of cast iron manhole cover must be greater than or equal to the reserved wellhead size, otherwise it will greatly affect the bearing capacity;

2. During the installation, the joint surface between the well base and the concrete ground must be close, and there shall be no hanging place, otherwise, it will be crushed by the roller and affect the service life during the construction and installation;

3. When installing the cast iron well cover on the asphalt pavement, it is necessary to avoid the construction machinery directly rolling the well base. During the pavement construction, the hole slightly larger than the well base shall be reserved on the pavement and placed after the asphalt pavement is completed. I don't know if you've noticed that in recent years, there have been fewer and fewer cases of lost manhole covers on the street. This is due to the continuous progress of social security, but on the other hand, the progress of "well cover technology" cannot be underestimated.

Determination principle of pouring position

a) During pouring, the main processing surface, main working surface and stress surface shall be placed at the bottom and side as far as possible to prevent sand holes, air holes, slag inclusions and other defects.

b) For the casting alloy with large shrinkage, it should meet the principle of sequential solidification, and the thick part of the casting should be placed on the top as much as possible to facilitate riser feeding.