英國PPM技術接口板ifB采樣裝置
英國PPM技術接口板ifB采樣裝置
英國PPM技術接口板ifB采樣裝置
英國PPM技術接口板ifB采樣裝置

英國PPM技術接口板ifB采樣裝置

價格

訂貨量(臺)

¥1000.00

≥1

聯系人 馬經理 客戶經理

掃一掃添加商家

ῡ῟῟῟῟ῧῨῨῧῦῥ

發貨地 河北省保定市
進入商鋪
掃碼查看

掃碼查看

手機掃碼 快速查看

在線客服

商品參數
|
商品介紹
|
聯系方式
產品名稱 采樣裝置
品牌 PPM
產地 英國
型號 ifB
模擬分辨率 16 位
電源供電 12v DC
輸入濃度 0-30°C
是否出口
加工定制
其他參數 參考詳情
商品介紹

產品名稱:ifB采樣裝置
品牌:PPM
產地:英國
型號:ifB


ifB采樣裝置介紹:


PPM 技術接口板 (ifB) 配有一個內置的 Formaldemeter 單元,旨在連接到第三方系統。接口板可配置不同電壓輸出;4-20mA電流輸出,同時提供繼電器報警輸出。有多種操作模式可供選擇,以適應各種用途、應用和情況。
有一個配置菜單可供用戶選擇輸出類型、操作模式、選擇輸出測試、采樣范圍以及校準 Formaldemeter。該菜單還允許在各種濃度下觸發內置的無電壓繼電器,以便控制外部設備。

典型用途:

  • 簡單集成到現有傳感器網絡
  • PLC控制系統
  • 獨立區域監控
  • 潔凈室;包裝室和車間
  • 單點遠程監控

PPM 技術接口板 (ifB) 配有 Formaldemeter htV,并且經過全面校準,可以立即使用。只需將外部輸出連接到 ifB 并打開即可。



ifB采樣裝置特點:





PPM 技術 ifB 裝置提供房間內當前甲醛水平的視覺顯示輸出。


來自內部 Formaldemeter 裝置的讀數顯示在屏幕上,為您提供快速簡便的空氣質量監測解決方案。



ifB 可用于三種采樣模式之一:

? 輪詢模式
在此模式下,僅當在采樣輸入線上檢測到有效脈沖時才會進行采樣。如果此時儀器還沒有充分清理以進行采樣,那么采樣將被延遲——一旦儀器準備好,就會進行采樣。這非常適合與 PLC 或其他基于控制器的系統一起使用,因為采樣率由輸入線路控制,并且當前狀態可作為輸出線路上的邏輯電平使用。

? 連續模式
該模式不需要任何外部觸發進行采樣。Formaldemeter 會盡可能頻繁地取樣。采樣持續時間將取決于樣品濃度(更高濃度的樣品將需要更長的時間來清除并延遲下一個樣品)。此模式易于設置,非常適合沒有基于控制器的系統可用且采樣頻率可能變化的應用。

? 定時模式
該模式不需要外部觸發,但與之前的連續模式不同,它使用內部定時器以設定頻率觸發樣本。這可以由用戶在 1 到 60 分鐘之間以一分鐘為增量進行調整。但是,不能保證采樣頻率,因為如果 Formaldmeter 未準備好在指定時間采樣,采樣可能會延遲。


ifB采樣裝置參數:

電源供電:12v DC(提供電源適配器),可根據要求提供高達 30v DC
輸入濃度:0-30°C,15-90%RH,0-10ppm(1ppb分辨率)
可選輸入 FSD:2.5ppm;5ppm、10ppm 或 100ppm
模擬輸出:0-2.5v;0-5v;0-10v;或 4–20mA
模擬分辨率:16 位(從零到 FSD 的 65536 步)
數字輸入/輸出:樣本、數據和錯誤
報警繼電器:額定0.5A@125VAC/2A@30VDC
高級功能:用于更改設置的簡單管理菜單;模擬測試模式和校準輸出周期;Formaldmeter校準程序;備份存儲在非易失性存儲器中的樣本



中文內容來自機器翻譯,內容僅供參考,實際內容可參考原廠介紹或以合同為準。
英文原文:



The ifB can be used in one of three sampling modes, depending on what best suits your needs. These are:

? Polled mode
In this mode samples are only taken when a valid pulse is detected on the sample input line. If the instrument has not cleared sufficiently to sample at this point then the sample will be delayed — as soon as the instrument is ready then a sample will be taken. This is ideal for use with PLC or other controller based systems as the sampling rate is controlled by the input lines and the current status is available as logic levels on the output lines.

? Continuous mode
This mode does not require any external trigger for sampling. Samples are taken as often as possible by the Formaldemeter. The sampling duration would be dependant on sample concentration (higher concentration samples will take longer to clear and will delay the next sample). This mode is easy to setup and is ideal for applications where no controller based systems are available and the sampling frequency can vary.

? Timed mode
This mode does not require an external trigger but unlike the previous continuous mode it uses an internal timer to trigger samples at a set frequency. This can be adjusted by the user between 1 and 60 minutes in increments of a single minute. However, the sampling frequency is not guaranteed as samples may be delayed if the Formaldmeter is not ready to sample at the designated time.


Instrument Specifications:
Mains Powered:12v DC (Mains adaptor available), up to 30v DC possible on request
Input Concentration:0-30°C, 15-90%RH, 0–10ppm (1ppb resolution)
Selectable Input FSD:2.5ppm; 5ppm, 10ppm or 100ppm
Analogue Outputs:0–2.5v; 0–5v; 0-10v; or 4–20mA
Analogue Resolution:16–bits (65536 steps from zero to FSD)
Digital I/O:Sample, Data & Error
Alarm Relay:Rated at 0.5A@125VAC/2A@30VDC
Advanced Features:Simple administration menu to change settings; Analogue test patterns & calibration output cycle; Formaldmeter calibration routine; Backup of samples stored in non-volatile memory

聯系方式
公司名稱 河北恒儀電子科技有限公司
聯系賣家 馬經理 (QQ:2044339890)
電話 ῧ῟ῡῨ-ῠῦῥῤῡῤῢ
手機 ῡ῟῟῟῟ῧῨῨῧῦῥ
地址 河北省保定市
聯系二維碼